First of all, it is the control of the temperature in the furnace. Industrial furnaces need to control the temperature during the heating process to achieve safe and stable production. However, if the control system in the furnace fails or is improperly adjusted, the temperature will be out of control, causing the temperature to be too high or too low, causing equipment failure or explosion.316L stainless steel vacuum brazing process In addition, due to the high temperature in the furnace, if you accidentally open the operation door or the observation port, etc., it may cause the staff to be burned by the heat in the furnace. Secondly, it is the damage and aging of the furnace body. Vacuum heat treatment of aluminum alloy die castings Due to the frequent work of industrial furnaces, the internal metal materials may be damaged and aged due to high temperature and corrosion. This situation will not only lead to a decrease in work efficiency, but may also cause cracks in the furnace body, which may cause an explosion. Therefore, regular inspection and maintenance is very necessary.Vacuum Oil Quenching for steel hardening heat treatment Furthermore, it is the leakage of energy supply materials such as gas and fuel oil. If these materials leak into the environment during operation, it may cause major hazards such as suffocation and poisoning to workers, and cause explosions and other accidents. Therefore, when using an industrial furnace, attention should be paid to checking the inside and outside of the furnace and the burner and other equipment to ensure that there is no leakage.MIM degreasing and sintering for ceramic hard alloy

All manual and automatic signals are input into PLC, all actions and logics are completely controlled by PLC, the performance is stable and reliable, the number of components is greatly reduced, and on-site debugging becomes convenient.Vacuum Heat Treatment of Fasteners Use a professional temperature controller to control the temperature. It has good temperature control and automatic adjustment, and controls the temperature with the optimal PID parameters. Compared with the temperature control program compiled by C language, the temperature control effect is greatly improved.Vacuum sintering of transparent ceramics The system consists of five parts: temperature control, pressure control, burner controller, inspection of workpiece temperature, upper computer control and software.Silicon Carbide Reaction Sintering Process After transformation, the furnace was fired again. During the heating process, the temperature deviation at 6 points was ≤ ± 10 ℃, and during heat preservation, the deviation was ≤ ± 4 ℃, with strong stability and reduced operation and maintenance costs. It has been used for more than 1 year, and there have never been failures such as crashes and data loss. The efficiency of the original equipment is greatly improved.Aluminum alloy and stainless steel vacuum brazing

Answer: First open the adjustment mode: (1) From the front room to the back room, press the forward button F3 of the pusher until the signal light 1 of the material hook hooked to the tray lights up, and then press the back button F4 of the push-pull device to move the tray Pull out until the material tray reaches the pulling position, the material hook is unhooked [unhook light 2 lights up] press F5 to open the middle door, press F3 to push the material tray into the back room, push it to the position and 4 lights up, the material hook returns to 5, The middle door is closed, the material hook returns to the original position, and the action stops.Vacuum sintered powder metallurgy parts (2) The material tray goes from the back room to the front room, firstly raise the lifting platform, press the F3 material hook to 11, open the middle door, stop the material hook to 4, then press F3, the material hook to the 13 grabbing position, Press F4, the material hook reaches 14, close the middle furnace door, the lifting table goes down to the oil tank, and the material hook returns to the original position.316L stainless steel vacuum brazing process Answer: When handing over shifts, you should first look at the shift book and record book, and go to the computer to check whether the process program and operating status are consistent with it. If it is normal, see if there is any special explanation. Whether the surface position is normal.Vacuum heat treatment of aluminum alloy die castings Look at various flowmeters to see if there are parts in the tempering furnace, and whether the material of the product is consistent with the temperature of the furnace, and then check whether the loading list is consistent with the prepared materials, whether it is standardized, whether the material of the test rod is correct, and finally go outside the workshop to see methanol, Whether the reserves of acetone, nitrogen, and ammonia are sufficient, understand the addition of methanol and acetone, and the opening status of the water pump.Vacuum Oil Quenching for steel hardening heat treatment

The radiation chamber is the part that conducts radiation heat transfer through flame or high temperature flue gas. This part is directly scoured by the flame and has the highest temperature, so the strength and heat resistance of the materials used must be fully considered. Ion Nitriding vs Gas Nitriding This part is the main place for heat exchange, and 70-80% of the heat load of the whole furnace is borne by the radiation chamber, which is the most important part of the whole furnace. It can be said that the pros and cons of a furnace mainly depends on the performance of its radiation chamber.Sintering of B4C by Pressureless Liquid Phase Sintering The size of the radiation chamber is mainly considered from the following three aspects: ①The thermal load of the radiation chamber and the average heat intensity of the outer surface of the radiant tube; ②The distance between the tube center and the tube wall; And the distance from the furnace tube to the flame.SISSOR TYPE HORIZONTAL MITER CUTTING BANDSAW BS-280G In order to facilitate operation and ensure safe operation, the radiation room of the tube furnace should be equipped with the following accessories: fire inspection door, manhole door, explosion-proof door, thermocouple casing, pressure measuring tube, fire extinguishing steam tube, etc.HORIZONTAL MITRE BAND SAW MACHINE BS-315GH

The full hydrogen bell furnace equipment includes a furnace platform, an inner cover, a heating cover, and a cooling cover. The process of the full hydrogen bell furnace is as follows: at the beginning of annealing, the steel coils to be annealed are stacked on the bell furnace platform, the inner cover is hoisted, and the cold state sealing test is carried out on the furnace platform, the inner cover system and the hydrogen inlet valve, and the test is successful. Finally, put the heating mantle button on the stove and carry out nitrogen purging;Aluminum alloy and stainless steel vacuum brazing When the nitrogen purge meets the conditions, replace the nitrogen in the inner cover with hydrogen; after the heating starts, select the heating curve according to different materials to control the temperature until the core temperature of the steel coil reaches the requirement; then remove the heating cover, and then hoist the cooling cover , using the surrounding ambient air to cool the inner cover through the fan on the cooling cover;Silicon Carbide Reaction Sintering Process When the thermocouple detects that the circulating atmosphere in the inner cover reaches the set temperature, the cooling cover fan stops running; after the temperature of the steel coil core reaches the set value, the cooling is completed, and the cooling cover is removed; then nitrogen is purged, The hydrogen in the inner cover is replaced, and the inner cover is removed; finally, the steel coil is lifted away, and a process is completed.HIGH SPEED CIRCULAR SAWING MACHINE HY-180NC After the production preparation is completed, the PLC will perform various media systems including water circulation, hydraulic system, protective gas and power supply, etc. After checking and judging that the safety system, measurement system and various hardware devices are working normally, issue a command to clamp the inner cover. After the inner cover is clamped, the control program will start each control program with a large time axis as a reference.CS SERIES COLD CUT CIRCULAR SAWS

ty

ty

ty

ty

ty

ty

ty

ty

ty

ty

ty

ty

ty

ty

ty